Pumps/Inflation

The Airchecker from SKS is a fast and easy way to check your tire pressure. The swiveling head makes it a snap to reach your valve stem at any angle, and the backlit display with extra-large LED digits is always easy to read. This gauge measures up to 144 psi.

• Compatible with Air Support HP, HP Pro, HV (429231, 429232, 429233, 429234, 429235)

Prestacycle redesigned the Presta Grommet in May 2012 to fit to modern standards. PRestacycle's design works so well, it’s been copied by others including major floor pump makers. Prestacycle's design engages the Presta valve just below the cap threads and requires less insertion. The head is now very easy to get on and off, and gives a nice “click” feeling when it’s installed in the right position. Safe for all types of Presta valves, including tubeless and tubeless-conversion valves. Will not harm newer lightweight performance valves. Fits all Prestaflator BIG Push/pull Presta heads. Also fits all Silca pump heads that use the 24.1 or 242 Gasket.

Renew all the seals in your Prestaflator spin head. These o-rings fit the seals, Plus there are five (5) Presta Valve replacement washers. Replace as needed for a good connection to your tire valve.

The Super Patch Kit is comprised of a small plastic case, a piece of sandpaper for roughing up the tube and 6 peel-and-stick patches so no gluing is required. The patches stick fast thanks to 3M technology and they're thin and flexy to stretch with the tube. There's no easier way to patch a tube.

Bag of 3 replacement washers for EVA heads on all SKS floor pumps

Made of heavy-duty hook-and-loop material, the Pump and U-Lock Tie also has a neoprene pad stitched next to the rectangular plastic common loop. Put the neoprene pad between your pump and frame, double-back the hook strip onto the loop, and you can rest assured that no matter how hard you ride, your pump will stay put. In addition to attaching pumps, the Pump Tie is also excellent for securing U-locks, fishing poles, and other delicate items that require a secure bond and a load-damping pad. - Dimensions: 1.5 x 10 inches - Weight: .5 ounces/14 grams

Prestacycle's newest version of the Presta Head Gasket uses Urethane Elastomer. It’s softer and stronger. It lasts more than 5 times longer, gives a better seal and flexes to work anywhere along the Presta shaft for better tubeless tire application.

There’s no easier or more effective way to patch a cut tire on the road or trail than carrying and using Park Emergency Tire Boots (3 per package). These thin, extra-tough patches peel and stick to the insides of tires to repair cuts and contain the tube until you can replace the tire.

Allows you to reach into difficult places with your Prestaflator hose. Great for cleaning and drying parts on-or-off the bike. If the tip is blocked, The safety feature releases air away from your work so you can maintain control. Can also be used to inflate low pressure vinyl-valve items (beach-ball type). The safety release feature will help prevent over-inflation. Made with 6061-T6 Alloy – it’s as strong as Brass and only 1/3 the weight. Note: The safety feature is only functional when the tip is used on a Prestaflator.

Use it to upgrade your floor pump or tankless electric inflator to use Prestaflator heads and accessories. Made with 6061-T6 Alloy – Strong as Brass and only 1/3 the weight. Hose clamp not included. The correct hose clamp varies based upon the outer diameter of your pump’s hose.

Replacement Composite Matrix pump mount for all High-Volume hand pumps (HV, Tech HV, Micro Floor HV/HVG, Alloy, Carbon Drives). Includes Velcro pump strap.

Lightweight plugs for tubeless tire punctures. When paired with Genuine Innovations' Tubeless Tackle Kit (#G20439) or Tubeless Repair Kit (#G2650), you can plug pesky punctures in seconds and cycle confident for many rides to come.

Planet Bike's line of CO2 replacement cartridges makes tire repairs quick and easy. - Planet Bike's CO2 cartridges work in Planet Bike inflators as well as most competitors' inflators. - Planet Bike cartridges are tested to the highest standards for durability, safety, and reliability. They contain pure CO2 with no oils or contaminants. - 100% recyclable steel cartridges - All threaded cartridges are compatible with Air Kiss, Red Zeppelin, Red Zeppelin 2 & Air Smith CO2

Braid-reinforced PVC hose is stronger than Prestacycle's original Black hose from a few years ago, and also twice flexible! Schrader Spin-on head accepts all Presacycle Head, new and old. 200 psi working pressure, 13 inches length. Uses standard 1/4" threads. Non-marring and resistant to moisture, fungi, oil, fuel, and grease as well as abrasion, impact, and tearing. Operating temperature range is from -30° to +125°F. Fits all previous Prestaflator tools, o-ring included.

MSW threaded CO2 Cartridges fit all MSW inflator heads as well as other manufacturer's inflators.

Planet Bike's 16-gram CO2 Cartridges are great replacement cartridges for your CO2 regulator. They are compatible with Planet Bike's Air Kiss, Red Zeppelin, Airship, and other manufacturers' inflators that use threaded cartridges.

If you own an Air-Bob inflator, you probably use it A LOT. When you finally wear out the original inflator head, no problem, here's the replacement part to get you back up and running.

You'll ride with peace of mind when you pack a can of Vittoria's Pit Stop Tire Sealant. It contains pure latex foam sealant and compressed air to quickly inflate and repair your tire so you can get on with your ride. Available in three sizes for varying tire volumes: - Road Racing: inflates 21-28-inch tubulars up to 94 psi and 700c clinchers up to 87 psi so you can ride, instead of walk to the closest pump and top off the tire to full pressure. - MTB 50 mL: Repairs and inflates low-volume MTB tires in less than a minute. - MTB Magnum 75 mL: Repairs and inflates meaty 27.5-inch tires and cross country 29-inch tires in less than a minute.

Give your tires a kiss of air with Planet Bike's Air Kiss CO2 Inflator. It fits Presta and Schrader valves, holds fast thanks to the thumblock head, and inflates in a jiffy. The cartridge is insulated with a sleeve to prevent frozen fingers during use, and the small size means the Air Kiss fits easily in bags, pockets and packs. A 16-gram cartridge is included.

Pssstttt. Tired of hearing that when you disconnect your shock pump? Well, hear it no more thanks to Topeak's Pressure-Rite. It's a must have for suspension fanatics as its ingenious design prevents air loss when adjusting shock and fork pressure. It's also available in a Presta version, perfect for disc wheels.

Threaded 16g CO2 cartridges for use with all Lezyne CO2 inflators. It inflates 700c road tire to 120psi (8.3bar) or one 26” MTB tire to 30psi (2.1bar). Sold in packs of five.

Planet Bike's MicroPro Mini-Pump inflates tires fast and easy thanks to its locking T handle, aluminum barrel and thumblock head. It fits all valves and comes with a frame mount for easy carrying.

Problem Solvers 90 degree Presta valve inflator is used to inflate disc wheels, thanks to its narrow, low-profile head. • Presta valve • 90 degree inflator works with most pump heads

- MSW threaded CO2 Cartridges fit all MSW inflator heads as well as non-MSW inflators - 38-gram threaded cartridges are sold individually

MSW Windstream Inflator Head is a push on inflation system. Compatible with all 3/8" threaded compressed gas cartridges. Works with Presta and Schrader. - Compact design for easy storage - Alloy construction for durability and lightweight - Press on for both Schrader and Presta valves - Compatible with all 3/8" threaded compressed air cartridges

A simple and reliable twist-to-inflate system, the Windstream Twist inflator head works with all 3/8" threaded inflation canisters — but with a twist. With no spring on the head, airflow is controlled by twisting the cartridge rather than pushing. Auto seals when not engaged. - Compact, lightweight design fits in tight spaces - Press-on for both Presta and Schrader valves - Compatible with 3/8” threaded cartridges - Rotate CO2 cartridge to regulate inflation - Kit includes CNC-machined aluminum inflator head with a green finish for better visibility

Lezyne's convenient Twin speed Drive CO2 inflator is compact and lightweight. Its aluminum head is compatible with both Presta and Schrader valves, and uses a simple twisting action for easy inflation. And, it accepts all threaded CO2 cartridges.

It’s back, the Pro’s favorite! Perfect for Tubeless tires, valve extenders and any Presta valve. It includes Prestacycle's newest version of the Mini Presta Head Gasket using Urethane Elastomer. It’s softer and stronger. It lasts more than 5 times longer, gives a better seal and flexes to work anywhere along the Presta shaft for any Presta application. Prestacycle's design engages the Presta valve just below the cap threads and requires less insertion. Deep head adapts to a wide variety of applications including valve extenders. The head is now very easy to get on and off. This head is a MUST for Tubeless tire users. Allows high-flow inflation with the valve core removed for seating tires. PUSH on / PUSH off – the fastest way to get you going. Made with nickel-plated 6061-T6 alloy – Strong as Brass and only 1/3 the weight. It’s also compatible with Silca pumps and can be adapted to other pump brands with our optional Schrader barb or our floor pump replacement hose. Patent-pending 2-way connector screws onto the Prestaflator threaded connector or directly clamps to a hose.

Topeak's incredibly compact CNC aluminum Threadlock Upgrade Kit threads directly to Presta or Schrader Valves with no need to change internal parts or use extra adapters. It fits most rubber pump hoses, and is compatible with Topeak JoeBlow Ace, JoeBlow Mountian, JoeBlow Sport II, JoeBlow Max II and JoeBlow Max HP.